當前位置:首頁   >    產品中心   >    熔體流速測試儀   >    熔融指數儀   >   熔融指數儀 廠家 產品展示

熔融指數儀 廠家

型 號

更新時間2023-08-04

廠商性質生產廠家

報價

產品描述:此款熔融指數試驗機為改良款,增加了眾多功能,在儀器配置、儀器使用壽命、操作便利性、測試精度方面有大幅提高,
具有國內一般熔融指數試驗機所*的優勢和性價比。

產品概述

產品名稱:熔融指數試驗機,熔體流動速率測定儀 


型號: BRR


一、滿足標準:

ISO 1133,ASTM D1238,GB/T3682

 

 

二、產品說明:

此款熔融指數試驗機為改良款,增加了眾多功能,在儀器配置、儀器使用壽命、操作便利性、測試精度方面有大幅提高,

具有國內一般熔融指數試驗機所*的優勢和性價比。



三、產品特點:

1、升溫速度快,超調量極小             2、恒溫精度高

3、在填料之后,能迅速恢復恒溫狀態     4、試驗參數校準并修正方便

5、可采用手動、自動切料試驗方法       6、中文液晶顯示 

7、配有打印機,將測試結果自動打印輸出



四、主要技術參數 

1、擠壓出料部分

出料口直徑:Φ2.095±0.005毫米,出料口長度:8.000±0.025毫米

裝料筒直徑:Φ9.550±0.025毫米,裝料筒長度:152± 0.1毫米

活塞桿頭直徑:9.475±0.015毫米,活塞桿頭長度:6.350±0.100毫米

2、標準試驗負荷(共8級全304#不銹鋼砝碼)

3、溫度范圍:常規室溫——400℃(500℃可選)

4、恒溫精度:±0.5℃  5、顯示分辨率:0.1℃

6、切料方式:可選手動或自動切料7、溫度恢復時間:小于4分鐘

8、打?。何⑿痛蛴C自動打印輸出 9、電源電壓:AC220V±10%   50HZ



五、配件

序 號 名  稱      單 位   數 量      備注

   1、 砝碼        套      1     計8件(1#在1級負荷內)

0.325㎏、1.2㎏、2.16㎏、3.8㎏、5.0㎏、10.0㎏、12.5、21.6k g

   2、  砝碼托盤    件      1        在1級負荷內

   3、  裝料斗      件      1         4、  口模清理棒  件      1

   5、 裝料桿      件      1         6、  料筒清理桿  件      1        組合件

   7、 活塞桿      件      1 (在1級負荷內)

   8、 口模        件      1         9、  水準儀      件      1

   10、紗布        卷      2         11、 打印紙      卷      2



六、儀器特點:

1、全套砝碼采用304不銹鋼材料制作,防止生銹影響外觀及砝碼精度

2、加熱筒采用304不銹鋼制作,因熔融指數試驗機長期在高溫下工作(zui高可達400~500度),高溫下金屬材料極易氧化生銹

3、雙傳感器配置,控溫精確,溫度梯度更好,壽命更長

4、按國標要求,加料后增加四分鐘倒計時功能

5、RS232接口,可直接連接電腦輸出數據(選配)

6、開機后可直接顯示上次測試條件,避免每次用戶都重新設置試驗參數,減少操作人員工作量

7、zui高溫度可達450~500度(訂貨時需特殊說明)

8、可長時間測試強腐蝕性塑料而無損儀器精度、

 

Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,Product Name: melt index tester, melt flow rate tester

Model: BRR

One, meet the standards:

ISO 1133, ASTM D1238, GB/T3682

Two, product description:

The melt index test machine is improved, increased the number of function, the instrument configuration, equipment life, convenient operation, measurement accuracy is greatly improved,

With the domestic general melt index test machine there is nothing comparable to this advantage and price.

Three, product characteristics:

1, fast heating speed, overshoot is small, high precision constant temperature 2

3, in the packing, can quickly restore the constant 4, test parameter calibration and correction of convenience

5, can use manual, automatic cutting test method 6, Chinese LCD display

7, equipped with a printer, the results of the test automatically print output

Four, the main technical parameters

1, extruding and discharging part

The outlet diameter: 2.095 ± 0.005 mm, outlet length: 8 ± 0.025 mm

The charging barrel diameter: 9.550 ± 0.025 mm, charging barrel length: 152 ± 0.1 mm

Piston rod head diameter: 9.475 ± 0.015 mm, length of piston rod head: 6.350 ± 0.100 mm

Test load of 2, standard (a total of 8 grade 304# stainless steel weight

3, the temperature range: conventional room temperature -- 400 ℃ (500 ℃ optional)

4, the precision of constant: ± 0.5 ℃, 0.1 ℃ display resolution: 5

The 6, cutting way: optional manual or automatic cutting 7, temperature recovery time: less than 4 minutes

8, printing: micro printer is used to print the output of 9, the power supply voltage: AC220V ± 10% 50HZ

Five, accessories

The sequence number name a number of notes

1, weight 1 meter 81# at 1 level load

0.325 kg, 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5, 21.6k G

2, weight tray 1 at 1 load

3, hoppers 14, die cleaning rod 1

5, charging 16 rods, cylinder cleaning rod 1 assembly

7, the rod of 1at 1 load

8, die 19, level 1

10, gauze volume 211, Volume 2 printing paper

Six, characteristics of the instrument:

1, a full set of weights adopts 304 stainless steel materials, prevent rust affect the appearance and weight precision

2, the heating cylinder adopts 304 stainless steel production, because the melt index test machine working under high temperature for a long timeup to 400~500, high temperature metal materials are easy to rust

3, dual sensor configuration, precise temperature control, temperature gradient is better, longer life

4, according to the national standards, the feeding after adding four minutes countdown function

5, the RS232 interface, can be directly connected to the computer output dataoptional)

6, after the boot can directly display the last test conditions, avoid every time the user to set the test parameters, reduce the workload of operators

7, the highest temperature can reach 450~500 degreeswhen ordering special instructions

8, long time test of strong corrosive plastic and nondestructive instrument accuracy,

 

留言框

  • 產品:

  • 您的單位:

  • 您的姓名:

  • 聯系電話:

  • 常用郵箱:

  • 省份:

  • 詳細地址:

  • 補充說明:

  • 驗證碼:

    請輸入計算結果(填寫阿拉伯數字),如:三加四=7
聯系人:陳丹
手機:
18911395947
點擊這里給我發消息
 
漂亮人妻被中出中文字幕久久,亚洲人成无码WWW久久久,久久久久无码精品国产,少妇高潮一区二区三区99
<蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <文本链> <文本链> <文本链> <文本链> <文本链> <文本链>